Delphi-PRAXiS - Delphi Problems with GPU temperature,S.M.A.R.T.(SCSI)

Hey i am new here!

I got some questions

1.)How to get SCSI S.M.A.R.T. .I got some code but i dont know how to use it (too complex).
Also if someone could help to get the temperature from the code...
Delphi-Quellcode:
			unit smart_drv;

interface

{$IFDEF KOL_MCK}

uses Windows, Messages, ShellAPI, KOL {$IFNDEF KOL_MCK}, mirror, Classes, Controls, mckControls, mckObjs, Graphics, 

mckObjs {$ENDIF};

{$ELSE}

{$I uses.inc}

  Windows, Messages, SysUtils, Variants, Classes, Graphics, Controls, Forms,

  Dialogs;

{$ENDIF}

procedure OpenSMART;

procedure ReadSMART;

procedure CloseSMART;

function  GetATTRName(attr:byte;var comm:string):string;

function GetFlags(flags:word):string;

procedure SwapBytes( var buf; count : integer );

Type

    TIDSECTOR = packed record

   wGenConfig:word;

   wNumCyls:word;

{   wReserved:word;}

   wNumHeads:word;

   wBytesPerTrack:word;

   wBytesPerSector:word;

   wSectorsPerTrack:word;

   wVendorUnique : array[0..2] of word;

   sSerialNumber:array[0..19] of char;

   wBufferType:word;

   wBufferSize:word;

   wECCSize:word;

   sFirmwareRev:array[0..7] of char;

   sModelNumber:array[0..39] of char;

   wMoreVendorUnique:word;

   wDoubleWordIO:word;

   wCapabilities:word;

   wReserved1:word;

   wPIOTiming:word;

   wDMATiming:word;

   wBS:word;

   wNumCurrentCyls:word;

   wNumCurrentHeads:word;

   wNumCurrentSectorsPerTrack:word;

   ulCurrentSectorCapacity:dword;

   wMultSectorStuff:word;

   ulTotalAddressableSectors:dword;

   wSingleWordDMA:word;

   wMultiWordDMA:word;

        hz           : array[1..72] of byte;

        LBA48        : array[0..5] of byte;

   bReserved:array[0..127] of byte;

        end;

    TGETVERSIONOUTPARAMS = packed record 

      version      : byte; 

      revision     : byte; 

      reserved     : byte;

      IDEDevMap    : byte; 

      Capabilities : dword; 

      reserved1    : dword; 

      reserved2    : dword; 

      reserved3    : dword; 

      reserved4    : dword; 

    End; 

    TIDEREGS = packed record

        bFeaturesReg:byte;      // Used for specifying SMART "commands".

        bSectorCountReg:byte;       // IDE sector count register

        bSectorNumberReg:byte;           // IDE sector number register

       bCylLowReg:byte;         // IDE low order cylinder value

       bCylHighReg:byte;      // IDE high order cylinder value

       bDriveHeadReg:byte;      // IDE drive/head register

       bCommandReg:byte;      // Actual IDE command.

       bReserved:byte;

    end;             // reserved for future use.  Must be zero.

 TSENDCMDINPARAMS = packed record

     cBufferSize:dword;      // Buffer size in bytes

      irDriveRegs:TIDERegs;      // Structure with drive register values.

      bDriveNumber:byte;      // Physical drive number to send

                     // command to (0,1,2,3).

      bReserved: array[0..3] of byte;      // Reserved for future expansion.

      dwReserved: array [0..4] of dword;      // For future use.

      bBuffer:array[0..1024*8] of byte;         // Input buffer.

    end;

 TDRIVERSTATUS = packed record

   bDriverError:byte;      // Error code from driver,

               // or 0 if no error.

   bIDEStatus:byte;        // Contents of IDE Error register.

               // Only valid when bDriverError

               // is SMART_IDE_ERROR.

   bReserved:array[0..3] of byte;   // Reserved for future expansion.

   dwReserved:array[0..1] of dword;// Reserved for future expansion.

  end;

   TDRIVEATTRIBUTE = packed record

          bAttrID:byte;      // Identifies which attribute

          wStatusFlags:word;   // see bit definitions below

         Value:byte;      // Current normalized value

         Worst:byte;   // How bad has it ever been?

         Raw:array[0..5] of byte;   // Un-normalized value

          bReserved:byte;      // ...

    end;

   TATTRTHRESHOLD = packed record

        bAttrID    : byte;

        bWarrantyThreshold : byte;

        reserved   : array[0..9] of byte;

    end;

 TSENDCMDOUTPARAMS = packed record

   cBufferSize  : DWord;      // Size of bBuffer in bytes

   DriverStatus : TDriverStatus;      // Driver status structure.

   attr         : array[0..255] of TDRIVEATTRIBUTE;         // Buffer of arbitrary length in which to 

store the data read from the                                  // drive.

    end;

   TSMARTATTRNAME = record

    value : word;

    name  : string[40];

    comm  : string[160];

   end;

   THDDInfo = record

    Model    : string;

    FW       : string;

    SN       : string;

    LBABits  : integer;

    LBASize  : int64;

    Cache    : integer;

   End;

var

  VersParams  : TGETVERSIONOUTPARAMS;

  SCOP        : array[0..3] of TSENDCMDOUTPARAMS;

  AttrCnt     : array[0..3] of word;

  hSMARTIOCTL : array[0..3] of thandle;

  IDSECTOR    : array[0..3] of TIDSECTOR;

  Thresholds  : array[0..3,0..255] of TATTRTHRESHOLD;

  HDDInfo     : array[0..3] of THDDInfo;

const

  PRE_FAILURE_WARRANTY       =     $01;

  ON_LINE_COLLECTION         =     $02;

  PERFORMANCE_ATTRIBUTE      =     $04;

  ERROR_RATE_ATTRIBUTE       =     $08;

  EVENT_COUNT_ATTRIBUTE      =     $10;

  SELF_PRESERVING_ATTRIBUTE  =     $20;

  IDENTIFY_BUFFER_SIZE        =     512;

  READ_THRESHOLD_BUFFER_SIZE =     512;

  SMART_READ_ATTRIBUTE_THRESHOLDS = $D1;

  IDE_ATAPI_ID           =     $A1;   // Returns ID sector for ATAPI.

  IDE_ID_FUNCTION        =     $EC;   // Returns ID sector for ATA.

var

   SCIP    : TSENDCMDINPARAMS;

const

   DFP_GET_VERSION        = $00074080;

   DFP_RECEIVE_DRIVE_DATA = $0007c088;

   DFP_SEND_DRIVE_COMMAND = $0007c084;

   SMART_ENABLE_SMART_OPERATIONS  = $D8;

   SMART_DISABLE_SMART_OPERATIONS = $D9;

   SMART_RETURN_SMART_STATUS     = $DA;

   SMART_CYL_LOW                  = $4F;

   SMART_CYL_HI                   = $C2;

   IDE_EXECUTE_SMART_FUNCTION     = $B0;

   READ_ATTRIBUTE_BUFFER_SIZE     = 512;

   SMART_READ_ATTRIBUTE_VALUES     = $D0;   // ATA4: Renamed

   AttrCount = 45;

   SmartAttrNames : array[1..AttrCount] of TSMARTAttrName=

   (

   (Value:1;Name:'Raw Read Error Rate';Comm:'Frequency of errors appearance while reading RAW data from a disk'),

   (Value:2;Name:'Throughput Performance';Comm:'The average efficiency of hard disk'),

   (Value:3;Name:'Spin Up Time';Comm:'Time needed by spindle to spin-up'),

   (Value:4;Name:'Start/Stop Count';Comm:'Number of start/stop cycles of spindle'),

   (Value:5;Name:'Reallocated Sector Count';Comm:'Quantity of remapped sectors'),

   (Value:6;Name:'Read Channel Margin';Comm:'Reserve of channel while reading'),

   (Value:7;Name:'Seek Error Rate';Comm:'Frequency of errors appearance while positioning'),

   (Value:8;Name:'Seek Time Performance';Comm:'The average efficiency of operations while positioning'),

   (Value:9;Name:'Power-On Hours Count';Comm:'Quantity of elapsed hours in the switched-on state'),

   (Value:10;Name:'Spin-up Retry Count';Comm:'Number of attempts to start a spindle of a disk'),

   (Value:11;Name:'Calibration Retry Count';Comm:'Number of attempts to calibrate a drive'),

   (Value:12;Name:'Power Cycle Count';Comm:'Number of complete start/stop cycles of hard disk'),

   (Value:13;Name:'Soft Read Error Rate';Comm:'Frequency of "program" errors appearance while reading data from a disk'),

   (Value:191;Name:'G-Sense Error Rate';Comm:'Frequency of mistakes appearance as a result of impact loads'),

   (Value:192;Name:'Power-Off Retract Cycle';Comm:'Number of the fixed "turning off" drive cycles (Fujitsu: Emergency 

Retract Cycle Count)'),

   (Value:193;Name:'Load/Unload Cycle Count';Comm:'Number of cycles into Landing Zone position'),

   (Value:194;Name:'HDD Temperature';Comm:'Temperature of a Hard Disk Assembly'),

   (Value:195;Name:'Hardware ECC Recovered';Comm:'Frequency of the on the fly errors (Fujitsu: ECC On The Fly Count)'),

   (Value:196;Name:'Reallocated Event Count';Comm:'Quantity of remapping operations'),

   (Value:197;Name:'Current Pending Sector Count';Comm:'Current quantity of unstable sectors (waiting for remapping)'),

   (Value:198;Name:'Off-line Scan Uncorrectable Count';Comm:'Quantity of uncorrected errors'),

   (Value:199;Name:'UltraDMA CRC Error Rate';Comm:'Total quantity of errors CRC during UltraDMA mode'),

   (Value:200;Name:'Write Error Rate';Comm:'Frequency of errors appearance while recording data into disk (Western 

Digital: Multi Zone Error Rate)'),

   (Value:201;Name:'Soft Read Error Rate';Comm:'Frequency of the off track errors (Maxtor: Off Track Errors)'),

   (Value:202;Name:'Data Address Mark Errors';Comm:'Frequency of the Data Address Mark errors'),

   (Value:203;Name:'Run Out Cancel';Comm:'Frequency of the ECC errors (Maxtor: ECC Errors)'),

   (Value:204;Name:'Soft ECC Correction';Comm:'Quantity of errors corrected by software ECC'),

   (Value:205;Name:'Thermal Asperity Rate';Comm:'Frequency of the thermal asperity errors'),

   (Value:206;Name:'Flying Height';Comm:'The height of the disk heads above the disk surface'),

   (Value:207;Name:'Spin High Current';Comm:'Quantity of used high current to spin up drive'),

   (Value:208;Name:'Spin Buzz';Comm:'Quantity of used buzz routines to spin up drive'),

   (Value:209;Name:'Offline Seek Performance';Comm:'Drives seek performance during offline operations'),

   (Value:220;Name:'Disk Shift';Comm:'Shift of disk is possible as a result of strong shock loading in the store, as a 

result of it`s falling or for other reasons'),

   (Value:221;Name:'G-Sense Error Rate';Comm:'This attribute is an indication of shock-sensitive sensor - total quantity 

of errors appearance as a result of impact loads '),

   (Value:222;Name:'Loaded Hours';Comm:'Loading on drive caused by the general operating time of hours it stores'),

   (Value:223;Name:'Load/Unload Retry Count';Comm:'Loading on drive caused by numerous recurrences of operations like: 

reading, recording, positioning of heads, etc.'),

   (Value:224;Name:'Load Friction';Comm:'Loading on drive caused by friction in mechanical parts of the store'),

   (Value:225;Name:'Load/Unload Cycle Count';Comm:'Total of cycles of loading on drive'),

   (Value:226;Name:'Load-in Time';Comm:'General time of loading for drive'),

   (Value:227;Name:'Torque Amplification Count';Comm:'Quantity efforts of the rotating moment of a drive'),

   (Value:228;Name:'Power-Off Retract Count';Comm:'Quantity of the fixed turning off`s a drive'),

   (Value:230;Name:'GMR Head Amplitude';Comm:'Amplitude of heads trembling (GMR-head) in running mode'),

   (Value:231;Name:'Temperature';Comm:'Temperature of a drive'),

   (Value:240;Name:'Head Flying Hours';Comm:'Time while head is positioning'),

   (Value:250;Name:'Read Error Retry Rate';Comm:'Frequency of errors appearance while reading data from a disk')

   );

   flagnames : array[0..5] of string[2] = ('PF','OC','PA','ER','EC','SP');

implementation

{------------------------------------------------------------------}

function GetFlags(flags:word):string;

var

  i : integer;

  s : string;

Begin

 s := '';

  for i := 0 to 5 do

    if flags and (1 shl i) <> 0 then

      s := s + flagnames[i]+#32;

 GetFlags := s;     

End;

{------------------------------------------------------------------}

function  GetATTRName(attr:byte;var comm:string):string;

var

  i : integer;

begin

  for i := 1 to attrCount do

   begin

    if attr = SmartAttrNames[i].Value then

     begin

      GetAttrName := SmartAttrNames[i].name;

      Comm := SmartAttrNames[i].comm;

      exit;

     end;

   end;

 GetAttrName := 'Unknown';

end;

{------------------------------------------------------------------}

procedure SwapBytes( var buf; count : integer );

Assembler;

Asm

        pushad

        mov     esi, buf

        mov     edi, esi

        mov     ecx, count

        shr     ecx, 1

        test    ecx, ecx

        jz      @@exit

        @@rep:

        lodsw

        xchg    ah, al

        stosw

        dec     ecx

        jnz     @@rep

@@exit:

        popad

End;

{------------------------------------------------------------------}

procedure OpenSMART;

var

  i       : integer;

  c       : dword;

  s, s1, s2   : string;

  os          : TOSVERSIONINFO;

  osver       : (wvNT3,wvNT4,wvW2k,wvXP,wv95,wv98,wvME);

begin

 for i := 0 to 3 do

  begin

 os.dwPlatformId := 0;

 os.dwOSVersionInfoSize := sizeof(OSVERSIONINFO);

 GetVersionEx( os );

    osver := wv98;

    case OS.DwMajorVersion of

      3:  osver := wvNT3;

      4:  case OS.DwMinorVersion of

            0: if OS.dwPlatformId = VER_PLATFORM_WIN32_NT

               then osver := wvNT4

               else osver := wv95;

            10: osver := wv98;

            90: osver := wvME;

          end;

      5:  case OS.DwMinorVersion of

            0: osver := wvW2K;

            1: osver := wvXP;

          end;

    end;

    hSMARTIOCTL[i] := 0;

    if (osver = wv98) or (osver = wv95) or (osver=wvME) then

    hSMARTIOCTL[i] := CreateFile('\\.\SMARTVSD', 0,0,NIL,

                        CREATE_NEW, 0, 0)

    else

     hSMARTIOCTL[i] := CreateFile(pchar( '\\.\PhysicalDrive'+format('%d',[i])),

                    GENERIC_READ or GENERIC_WRITE,

                    FILE_SHARE_READ or FILE_SHARE_WRITE,

                    NIL,

                    OPEN_EXISTING,

                    0,

                    0);

     if hSMARTIOCTL[i] = INVALID_HANDLE_VALUE then continue;

     DeviceIoControl(hSMARTIOCTL[i], DFP_GET_VERSION,

           NIL,

           0,

           @VersParams,

           sizeof(VersParams),

           c, NIL) ;

        FillChar( SCIP, SizeOf( SCIP ), 0 );

   SCIP.cBufferSize := 0;

   SCIP.irDriveRegs.bFeaturesReg := SMART_ENABLE_SMART_OPERATIONS;

   SCIP.irDriveRegs.bSectorCountReg := 1;

   SCIP.irDriveRegs.bSectorNumberReg := 1;

   SCIP.irDriveRegs.bCylLowReg := SMART_CYL_LOW;

   SCIP.irDriveRegs.bCylHighReg := SMART_CYL_HI;

   //

   // Compute the drive number.

   //

   SCIP.irDriveRegs.bDriveHeadReg := $A0 or (( i and 1) shl 4);

   SCIP.irDriveRegs.bCommandReg := IDE_EXECUTE_SMART_FUNCTION;

   SCIP.bDriveNumber := i;

        DeviceIoControl(hSMARTIOCTL[i], DFP_SEND_DRIVE_COMMAND,

                @SCIP, sizeof(TSENDCMDINPARAMS) - 1,

                @SCOP[i], sizeof(TSENDCMDOUTPARAMS) - 1,

                c, NIL);

   SCIP.cBufferSize := IDENTIFY_BUFFER_SIZE;

   SCIP.irDriveRegs.bFeaturesReg := 0;

   SCIP.irDriveRegs.bSectorCountReg := 1;

   SCIP.irDriveRegs.bSectorNumberReg := 1;

   SCIP.irDriveRegs.bCylLowReg := 0;

   SCIP.irDriveRegs.bCylHighReg := 0;

   SCIP.irDriveRegs.bDriveHeadReg := $A0 or ((i and 1) shl 4);

   SCIP.irDriveRegs.bCommandReg := IDE_ID_FUNCTION{ or IDE_ATAPI_ID};

   SCIP.bDriveNumber := i;

   SCIP.cBufferSize := IDENTIFY_BUFFER_SIZE;

        DeviceIoControl(hSMARTIOCTL[i], DFP_RECEIVE_DRIVE_DATA,

        @SCIP, sizeof(TSENDCMDINPARAMS) - 1,

        @SCOP[i], sizeof(TSENDCMDOUTPARAMS) + IDENTIFY_BUFFER_SIZE - 1,

        c, NIL) ;

        Move(SCOP[i].attr, IDSECTOR[i], SizeOf( IDSECTOR[i] ) );

        SCIP.cBufferSize := READ_THRESHOLD_BUFFER_SIZE;

        SCIP.irDriveRegs.bFeaturesReg := SMART_READ_ATTRIBUTE_THRESHOLDS;

        SCIP.irDriveRegs.bSectorCountReg := 1;

        SCIP.irDriveRegs.bSectorNumberReg := 1;

        SCIP.irDriveRegs.bCylLowReg := SMART_CYL_LOW;

        SCIP.irDriveRegs.bCylHighReg := SMART_CYL_HI;

        SCIP.irDriveRegs.bDriveHeadReg := $A0 or ((i and 1) shl 4);

        SCIP.irDriveRegs.bCommandReg := IDE_EXECUTE_SMART_FUNCTION;

        SCIP.bDriveNumber := i;

        DeviceIoControl(hSMARTIOCTL[i], DFP_RECEIVE_DRIVE_DATA,

        @SCIP, sizeof(TSENDCMDINPARAMS) - 1,

        @SCOP[i], sizeof(TSENDCMDOUTPARAMS) + READ_THRESHOLD_BUFFER_SIZE - 1,

        c, NIL) ;

        Move( SCOP[ i ].attr, Thresholds[ i ], SizeOf( Thresholds[ i ] ) );

        HDDInfo[ i ].LBASize := 0;

        HDDInfo[ i ].LBABits := 28;

   if idsector[i].ulTotalAddressableSectors = $FFFFFFF then

      begin

       move( idsector[i].lba48,HDDInfo[ i ].LBASize,6);

       HDDInfo[ i ].LBABits := 48;

      end

         else

       move( idsector[i].ulTotalAddressableSectors,HDDInfo[ i ].LBASize,4);

       s := IDSECTOR[i].sModelNumber +#32;

       SwapBytes( s[1], Length(s) );

       While (Length(s)<>0) and (s[Length(s)-1]=#32) do

         SetLength( s, length(s)-1);

   HDDInfo[ i ].Model := s;

   s := IDSECTOR[i].sFirmwareRev +#32;

   SwapBytes( s[1], Length(s) );

   HDDInfo[ i ].FW := s;

   s := IDSECTOR[i].sSerialNumber+#32;

   SwapBytes( s[1], Length(s) );

    While (Length(s)<>0) and (s[1]=#32) do

     delete(s,1,1);

   HDDInfo[ i ].SN := s;

   HDDInfo[ i ].Cache := IDSECTOR[i].wBufferSIze div 2;

  end;

end;

{------------------------------------------------------------------}

procedure CloseSMART;

var

  i : integer;

Begin

 for i := 0 to 3 do

     CloseHandle(hSMARTIOCTL[i]);

End;

{------------------------------------------------------------------}

procedure ReadSMART;

var

  i,j     : integer;

  c       : dword;

Begin

OpenSMART;

 for i := 0 to 3 do

  begin

     if hSMARTIOCTL[i] = INVALID_HANDLE_VALUE then continue;

   SCIP.cBufferSize := READ_ATTRIBUTE_BUFFER_SIZE;

   SCIP.irDriveRegs.bFeaturesReg := SMART_READ_ATTRIBUTE_VALUES;

   SCIP.irDriveRegs.bSectorCountReg := 1;

   SCIP.irDriveRegs.bSectorNumberReg := 1;

   SCIP.irDriveRegs.bCylLowReg := SMART_CYL_LOW;

   SCIP.irDriveRegs.bCylHighReg := SMART_CYL_HI;

   //

   // Compute the drive number.

   //

   SCIP.irDriveRegs.bDriveHeadReg := $A0 or (( i and 1) shl 4);

   SCIP.irDriveRegs.bCommandReg := IDE_EXECUTE_SMART_FUNCTION;

   SCIP.bDriveNumber := i;

        FillChar( SCOP[i], SizeOf( SCOP[i] ), 0 );

        DeviceIoControl(hSMARTIOCTL[i], DFP_RECEIVE_DRIVE_DATA,

                @SCIP, sizeof(TSENDCMDINPARAMS) - 1,

                @SCOP[ i ], sizeof(TSENDCMDOUTPARAMS) - 1 + READ_ATTRIBUTE_BUFFER_SIZE,

                c, NIL);

     AttrCnt[ i ] := 0;

     for j := 0 to 255 do

      if SCOP[ i ].attr[ j ].bAttrID = 0 then

       begin

         AttrCnt[ i ] := j;

         break;

       end;

  end;

 CloseSMART;

End;

{------------------------------------------------------------------}

end.
2.)How to get GPU temperature and enviroment temperature (ATI&NVIDIA)?
3.)How to get memory info(voltage,refresh rate,latency,precharge,type,fsb:dram)?
4.)How to do cpu usage for core 2 duo and core 2 quad?

Thanks in advance! :)